Metal Casting Release Agent

Home > Metal Casting Release Agent

Mould Release Agent for Aluminum Die Casting 

Item No.: MK-TP
Sakurai  MK-TP environmental protection type aluminum alloy mold release agent is suitable for large complex die casting, auto parts, complex core pulling piece, complex LED radiator, radiator, largecommunication  of large pump etc.. Not contain
INQUIRY Buy At Alibaba
Description


            Mould Release Agent for Aluminum Die Casting

Product features

1.Superior performance

Sakurai mould Release agent sprayed onto the mold surface. The effective ingredients of the formation of dense films immediately. The membrane resistance to high pressure, Nai Chongshua, low coefficient of friction on the injection process (0.08mm-0.15mm), effectively prevent the die casting products and mold welding. To prevent from the type of anti adhesive product variant. At the same time the lubrication performance of excellent speed up the liquid aluminum liquidity, the aluminum liquid can quickly formed in the cavity. To avoid the product defects and strain.

2. special surface finish

Sakurai series using rare special materials. It can effectively solve the casting surface blackening, water too much and avoid cold insulation. To solve the product after processing, such as: polishing and electroplating and other problems.

3.fully protect the mould release agent

Sakurai in the mold surface to form a layer of protective film. Effectively reduce the aluminum liquid heat and mechanical impact on the action of mould. The correct selection of high quality mold release agent can effectively protect the mould, prolong die service time, reduce the times of repairing die.

4.no carbon property

Sakurai release agent used is very simple and convenient operation. No carbon deposition, no mold fouling, does not produce oxide skin. Reduce the times of mould and die Province, cleaning products, bright, smooth surface, without affecting the subsequent polishing and electroplating, spray surface treatment.

5.high temperature resistant performance superior

Sakurai release agent has good thermal stability and chemical stability. Temperature range in the use of no oxidation, no burning, no corrosion of mold and the surface decomposition residues. Even in the high temperature of 300 DEG C, the first few (heat first heavy weight not exceeding 10%). To ensure that, under the conditions of high temperature, mold release film forming strong on the mold. To suppress the high temperature burn clean. Lubrication and demoulding effect.

6.good cooling effect

Sakurai release agent in the die casting process to effectively control the mould was constantly high temperature liquid metal is heated and the temperature rise, high mold temperature make die casting defects. Such as: sticking to mould, blistering, cracking and burn. At the same time the mold to mold material containing long-term high temperature work intensity decreased, resulting in decreased and the service life of the die crack.

7.high safety performance

Sakurai release agent non-toxic, non flammable, non corrosive, no chemical reaction. In the use of the process does not contain harmful smoke. No residual die and the surface of the product, cleaning and maintenance easy, wash the net, does not affect the subsequent processing.

⊙The physicochemical data

Smell

Low odor

Density (H2O)

1.10 PH

Appearance

Milky white liquid

The use of temperature

200℃-300℃

Flash point (COC)

Not applicable

Refraction coefficient@20℃

1.2

Freezing point

-10℃

Ph(5%diluent)

7


⊙Usage description

1.Dilution ratio please according to the spot technology personnel deployment test concentration, and finally determine the optimum dilution ratio!

2.If more than the typical usage outside the range please contact us for technical support.

3.When mixed with water use (the concentrated liquid added to the water dilution).

4.Please use deionized water to dilute, helps to prolong the working fluid life, reduce the use amount of concentrated liquid, fully reflect the working fluid properties.

5.Unless the technical services department shall not be allowed, add other substances to concentrate and dilution.

6.Concentration control of the concentration of percentage content can be obtained by dilution liquid refractometer and refraction coefficient.

⊙Notice

1.Die releasing agent must use pure water dilution,gently shaking or stirring use; dilution ratio according to the casting mould depth Complexity, make the appropriate adjustments.

2.Using a gun or spraying automatic system, pay attention to uniform spraying and Dry.The best use of temperature

3.Working temperature is 200℃ -350℃.

4.Die releasing agent in normal temperature, pay attention to antifreeze sunscreen, Kaifeng attention after the sealing cover good custody.



1. Are you a manufacturer or a trader?
We are one of largest manufacturer of Mold Release Agents in China.
2. Do you supply free sample?
We supply free sample within 1kg and you got to pay for courier freight cost. The trial cost we refund to you on bulk order.
3. Do you supply concentrate or ready-to-use release agent?
Based on your choice, concentrate and ready-to-use are both available for your purchasing.
4. What is your shipping method and transportation?
For sample,we mostly deliver small packages by Fedex/DHL/TNT air cargo with door-to-door service, which are safe and reliable for chemical liquid delivery. For bulk order, sea transportation is our first choice to save shipping cost. We make efforts to satisfy your specify requirements.
5.What is your suggestions for sample trial?
First, We suggest that everytime you use a small quantity of samples to test. Because the quantity of samples is limited, PLEASE do not use up all the samples for testing in one-time. so you can test samples for many times. If first time testing is failed, then we can have a second chance to adjust the testing process. You should adjust a suitable dilution ratio according to the specific practical testing.

TOP