Metal Casting Release Agent

Home > Metal Casting Release Agent

Pure Aluminum die casting lubricant

Item No.: MK-TL
INQUIRY
Description


Pure Aluminum die casting lubricant

Product features
1. Excellent demolding performance
When SAKURAI aluminum release mould spray is sprayed to the mould surface, its Effective ingredients form dense film at once. The membrane in the injection process is High pressure resistant, scouring resistant, low friction coefficient, effectively prevents Die-casting products to soldering with the mould. At the same time the excellent Lubrication performance speeds up the flowing aluminum liquid, so that the aluminum Liquid can rapidly form a mould.
2. Excellent surface brightness
SAKURAI  release mould spray  adopt rare and special materials. It can effectively solve The problems such as casting surface turns black, too much water lines and cold shut. Can solve the problems happening in postprocessing, such as: polishing and Electroplating.
3. Fully protect mold
SAKURAI release mould spray forms a protective film on the mould surface. Effectively Reduce the heat for the mould and reduce the impact from the liquid aluminum to the Machine. Correct selection of high quality mould release mould spray can effectively Protect the mould , prolong the life of the mould and reduce the repair.
4. No carbon deposition
SAKURAI  release mould spray  is very easy to use. No carbon deposition, no in-cavity Deposition , no mold scale and no oxide skin. Reduce the times to clean the mould, and if You use this  release mould spray  the product surface will be bright and clean, does not Affect the subsequent spray plating, polishing and surface treatment.
5. Excellent high temperature resistant performance
SAKURAI  release mould spray  has good thermal stability and chemical stability. In the Using range of temperature it do not oxidize, not burn, not corrode the mould and not Resolve residues on the mould surface. Even at high temperature 300 °C, weight lost few (thermal weight loss not more than 10%). Thus assure, at the high temperature, a Strong demoulding film is formed on the mold. Restraining high temperature sintering, Reach the role of lubrication and demoulding.
6. Good cooling effect
In die casting process because of the high temperature, mould has been heating ,the Temperature of liquid metal rises, and the high mold temperature makes die casting Defect. SAKURAI  release mould spray  effectively controls these problems .Such as: Soldering, blistering, cracking, and burned.
7. High safety performance
SAKURAI release mould spray is non-toxic, non-flammable, no corrosion, no chemical Reaction. In the process of use SAKURAI release mould spray does not contain harmful Smoke.

 
Physical and chemical data

Appearance:

Milky white liquid

Smell:

Little smell

Using temperature:

200°C-300°C

Freezing point:

-10℃

Density(H2O):

1.10 PH

Refraction coefficient@20℃:

1.2

PH(5%diluent):

7

Solid content:

30%

 
Usage
1.Please finally determine the best dilution ratio according to test Concentration deployed by the technology personnel.
2.If your usage will be excess the typical usage please contact us for technical support.
3.Mix with water after use (diluted concentrate liquid with the water ). 
4.Please use deionized water to dilute, helping to prolong the life of working liquid, Reduce the usage of concentrate , fully reflects the performance of the processing fluid.
5.Unless the technical services allow , do not add other material to concentrate and Diluent.
6.The concentration of control may be achieved through the refractometer and Refraction coefficient of diluent concentration percentage.


Notice
1.Die-casting  release mould spray must dilute with pure water, and gently shake or stir when you use; Dilution ratio is appropriately Adjusted according to the complexity of the casting and the depth of the mould.

2. Using the spray gun or automatic system to spray, pay attention to spray evenly and Blow dry.

3.The best using temperature of the mould is 200 °C to 300 °C.

4. Die-casting mould release mould spray stored under normal temperature, pay attention to prevent frostbite prevent bask in, after opening pay attention to hermetic seal and Store well.

1. Are you a manufacturer or a trader?
We are one of largest manufacturer of Mold Release Agents in China.
2. Do you supply free sample?
We supply free sample within 1kg and you got to pay for courier freight cost. The trial cost we refund to you on bulk order.
3. Do you supply concentrate or ready-to-use release agent?
Based on your choice, concentrate and ready-to-use are both available for your purchasing.
4. What is your shipping method and transportation?
For sample,we mostly deliver small packages by Fedex/DHL/TNT air cargo with door-to-door service, which are safe and reliable for chemical liquid delivery. For bulk order, sea transportation is our first choice to save shipping cost. We make efforts to satisfy your specify requirements.
5.What is your suggestions for sample trial?
First, We suggest that everytime you use a small quantity of samples to test. Because the quantity of samples is limited, PLEASE do not use all the samples for testing in one-time. so you can test samples for many times. If first time testing is failed, then we can have a second chance to adjust the testing process. You should adjust a suitable dilution ratio according to the specific practical testing.

 

TOP